They are making several good observations related to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround in general in this post in the next paragraphs.
Setting up a bath tub isn't exactly rocket science, however it does require solid plumbing, woodworking, and also in some cases, tiling abilities. Replacing an old tub with a brand-new one is also a moderately hard project. If the old tub is conveniently accessible, the project can move immediately; if you have to open up a wall to eliminate the old bathtub and place the new tub, the job is much harder. In either instance, the project is within a house handyman's abilities, although you will require a helper to leave the old bathtub and embeded in the brand-new one. Ensure you have actually certified yourself for the task and are comfortable trying it. Rather than employing a service provider to take over a halfway-completed job, it is far better to consider utilizing one prior to you begin. Chances are you may require a specialist plumber to make tube connections.
This short article will help you install a new tub in your washroom if you have already gotten a brand-new bathtub and don't require to transform the arrangement of your previous supply of water pipelines.
Your devices and also material checklist ought to make up the following:
Preparing for the Installment
To start with, the sustaining structure supplied with the bath ought to be fitted (if needed) according to the maker's guidelines. Next off, fit the faucets or mixer to the bathtub. When fitting the tap block, it is very important to see to it that if the faucet features a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bath, it is also practical to fit a sustaining plate under the faucets unit to prevent strain on the bathtub.
Fit the flexible faucet adapters to the bottom of the two taps utilizing 2 nuts as well as olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet with the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make certain you utilize all of the supplied washers.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bath need to currently prepare to be fitted in its final placement.
Removing Old Touches
If you require to replace old taps with brand-new ones as a part of your installment, then the first thing you should do is separate the water. After doing so, switch on the taps to drain pipes any kind of water staying in the system. The process of removing the existing faucets can be rather problematic as a result of the limited access that is frequently the instance.
Make use of a basin wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipelines to the taps. Have a fabric ready for the continuing to be water that will come from the pipelines. When the supply pipelines have actually been removed, make use of the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from turning throughout this process. Once the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned up of any old securing compound.
Prior to proceeding to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Setting up the Bath tub
Utilizing both wooden boards under its feet, position the bathtub in the called for setting. The wood boards are valuable in evenly spreading out the weight of the bath tub over the area of the boards rather than concentrating all the weight onto four tiny factors.
The next objective is to guarantee that the bath tub is leveled all round. This can be achieved by inspecting the level as well as readjusting the feet on the bathtub till the spirit level checks out degree.
To install faucets, fit all-time low of the furthest versatile faucet port to the proper supply pipeline by making a compression join; after that do the very same for the other faucet.
Activate the supply of water and also check all joints as well as brand-new pipework for leakages and tighten them if needed. Load the bathtub and additionally check the overflow outlet as well as the regular outlet for leaks.
Lastly, deal with the bath paneling as explained in the maker's user's manual. Tiling and sealing around the tub needs to wait until the bathtub has been utilized at the very least when as this will certainly resolve it right into its last position.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will require a plastic adapter to prevent damage to the thread. One end of the port fits on the plastic tail of the faucet and the other end supplies a link to the current supply pipelines.
If you require to fit a monobloc, then you will certainly need decreasing couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next off, place the faucet in the placing hole in the bath/basin guaranteeing that the washers are in location between the tap as well as the sink. Protect the tap in place with the manufacturer provided backnut. As soon as the faucet is firmly in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with typical tap ports. The former type ought to be connected to the tap ends first, tightening up just by hand. The supply pipelines can later on be linked to the various other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Tub
In the location where the bath satisfies the tile, it is needed to secure the joins with a silicone rubber caulking. This is very important as the fitting can move sufficient to fracture an inflexible seal, triggering the water to permeate the wall between the bathroom and also the tiling, causing issues with dampness and feasible leakages to the ceiling below.
You can pick from a range of coloured sealers to assimilate your components as well as installations. They are marketed in tubes and also cartridges, as well as can securing voids approximately a size of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with spins of drenched paper or soft rope. Keep in mind to always fill the bath tub with water prior to securing, to allow for the movement experienced when the bathtub remains in usage. The sealant can crack fairly very early if you do not think about this activity prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also conveniently offered on the market. It is advisable to fit the floor tiles making use of water-resistant or waterproof glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I stumbled upon that blog posting on How to Install a Bathtub Yourself when doing research the search engines. So long as you enjoyed our blog post please do not forget to pass it around. Thanks for your time invested reading it.
Book Service Now